Joyor S Series Electric Scooter Display: Usage Guide and Troubleshooting

Comments · 58 Views

The best electric scooters for travel

This article will provide detailed usage guide and troubleshooting methods for Joyor S series electric scooters display instrument, applicable to Joyor S5, S8-S, S10-S and other electric scooters equipped with Z-930 display models. Whether you are a beginner or daily user, this article will help you master the various functions and operation skills of the instrument. We also list the error codes to help you troubleshoot problems when the scooter malfunctions.

Basic Operation Guide

The Joyor S Series Electric Scooter's display is simple in design and powerful in function. Here are some basic operations:

Power on/off: Short press the power button to turn the power on/off.

Headlight switch: Short press the power button on the main interface to turn the headlight on/off.

Adjust the gear position: Short press the +- keys on the main interface to adjust the gear position to meet different speed requirements.
Enter special mode

6KM push mode: Long press the - key to enter this mode for manual pushing.

Menu setting page: Long press the M key for 3 seconds to enter the menu setting page for more advanced settings.

P MODE

The P value corresponding to the setting interface represents

the corresponding content. The specific status is as follows:

   P Value.Definition
P02Mileage unit ,0: KM; 1: MILE; default: 0
P03Voltage mode; default: 48V
   P04Sleep time: from 0-60mins (0 means always on,
default: 5mins)
   P06Wheel diameter: calculated by inch; precision:
0.1; default: 10
   P07Number of tachometer magnets: Range: 1-100;
Default: 30
   P09Zero start/non-zero start settings, 0: Zero start;
1: Non-zero start; Default: 1
   P10Smart speed limit settings, 0: Speed released,
1: Speed locked; Default: 0
    P12Activate strength setting. Range: from 0 to 5,
5 most power; Default: 5
   P15
Motor drive signal percentage setting, Range: from 1 to
100; Default: 100
   P16
Auto cruise setting, 1: Auto cruise Activated; 0: Auto cruise
Locked; Default: 0
   P99Restore to initial settings

 

Enter the menu, short press the plus or minus key, the value 00099 flashes,

and the display returns to the main interface after long pressing the plus key

for 5 seconds. The setting is successfully done.

ODO: To clear ODO

In the ODO parameter setting interface, briefly press the + button and then

press and hold for 5–6 seconds until the number is zero.

 

Joyor S5 S8-S S10-S E-Scooter Fault diagnosis code

ERRO 1: Rear motor failure
Check if the motor wire, Hall and phase wire are loose
Re-insert the loose motor wire and Hall wire and fix them.

ERRO 11: Front motor failure
Check if the motor wire, Hall and phase wire are loose
Re-insert the loose motor wire and Hall wire and fix them

ERRO 2: Throttle failure
Check if the throttle wire plug-in is plugged in
If the plug-in is detached, re-insert it in place and fix it

ERRO 3: Controller failure
Check if the motor and controller wire, Hall and phase wire are loose Re-insert the loose motor wire and Hall wire and fix it

ERRO 4: Power-off brake handle failure
You can unplug the brake handle wire and try to judge whether it is a brake handle failure or a controller failure

ERRO 5: Undervoltage protection
Check if the charging cable is detached and does not charge. If the plug-in is detached, re-insert it in place and fix it

ERRO 6: Controller communication failure
Check if the main line and instrument plug-in or the main line and controller plug-in are plugged in. If the plug-in is detached, re-insert it in place and fix it

ERRO 7: Instrument communication failure
Check the main line and instrument plug-in or the main line and controller plug-in to see if they are properly plugged in. If the plug-in is detached, re-insert it and fix it in place.

ERRO 9: High temperature protection failure 

The controller temperature is too high. Cool down for a few minutes and restart the machine to ride.

If you still can't fix the problem after trying the above, you may need to replace the corresponding part to solve the problem. You can find any repair parts you need in our store.

Special operation tips

Clear ODO total mileage: Press and hold the power button for 10 seconds, the screen backlight will light up to indicate that the clearing is successful.

By mastering the above operations, you will be able to make full use of the display instrument of the Joyor S series electric scooter and enjoy a safer and more convenient riding experience. If you encounter any problems, you can also contact us

Comments